manualshive.com logo in svg

SolarEdge storedge, Installation Manual

Share
Download
SolarEdge storedge Installation Manual Download Page 16

NOTE

Images are for illustration purposes only. Refer to the label on the product to identify the plus and 

minus input and output connectors.

Step 3: Connecting Power Optimizers in Strings

You can construct parallel strings of unequal length, that is, the number of power optimizers in each 
string does not have to be the same. The minimum and maximum string lengths are specified in the 
power optimizer datasheets. Refer to the SolarEdge Site Designer for string length verification.

NOTE

The total cable length of the string (including power optimizers’ cables)  should not exceed 

1000ft./300m from DC+ to DC- of the inverter. Use at least 11 AWG/ 4 mm² DC cables.

 1. Connect the Minus (-) output connector of the string’s first power optimizer to the Plus (+) output

connector of the string’s second power optimizer.

 2. Connect the rest of the power optimizers in the string in the same manner.

Figure 6: Power optimizers connected in series

 3. If you intend to monitor the installation, using the SolarEdge monitoring portal, record the physical 

location of each power optimizer, as described in 

Providing Installation Information

 on page 61.

WARNING!

Input and output connectors are not watertight until mated. Open connectors should be mated to 

each other or plugged with appropriate watertight caps. 

Les connecteurs d’entrée et sortie ne sont pas étanches jusqu'à ce qu’ils soient accouplés. Les 

connecteurs doivent être accouplés ou fermés avec des terminaux étanches.

Chapter 2: Installing the Power Optimizers

SolarEdge

-

StorEdge Installation Guide MAN-01-00262-1.0

15

Summary of Contents for storedge
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands