Solarbayer BioX 15 Operating Instructions Manual Download Page 49

Page: 49 / 80

Maintenance and cleaning

10.10

Lambda sensor cleaning

The lambda sensor of the BioX wood log boiler must be checked once a year for dirt or cleaned.

Attention:

The lambda

sensor  can  easily  be
damaged,  so  handle  it  with
care  during  operation.  A
damaged  lambda  sensor
does  not  guarantee  clean
combustion

and

must

therefore be replaced.

The lambda sensor is
heated during operation!
Danger of burns!

Recommendation: Clean the lambda sensor in system state 1 "OFF":



Disconnect the system from the power supply



Remove the two top cover parts



Unplug the white plug connection of the lambda sensor (see picture)





Remove the top back cover (4 screws torx)





Carefully unscrew the lambda sensor using a suitable

socket wrench





Carefully clean the sensor with a clean, dry cloth



Carefully reinsert the sensor and screw it in place



Reconnect the lambda sensor to the control board

Mount the boiler covers again

IMPORTANT!

DO NOT

install or remove with

pliers! Damage caused by incorrect
handling will not be refunded!

Summary of Contents for BioX 15

















































































Search results

Summary of Contents for BioX 15

Reviews:

Related manuals for BioX 15

Brands by name

Popular brands

Solarbayer BioX 15, Operating Instructions Manual

Search results

Summary of Contents for BioX 15

Reviews:

Related manuals for BioX 15

Brands by name

Popular brands