manualshive.com logo in svg

Ski-Doo 2005 MACH Z, Shop Manual, Page: 54 / 343

Share
Download
Ski-Doo 2005 MACH Z Shop Manual Download Page 54

Section 02 ENGINE

Subsection 04 (ENGINE REMOVAL AND INSTALLATION)

2

1

A35C24A

ENGINE SUPPORT NUTS REMOVAL

1. Nuts
2. Engine support

Remove both spark plugs.

Install in the MAG side spark plug hole the spark
plug lift ring (P/N 529 035 830).

Using the engine removal hook (P/N 529 035 829),
lift engine until engine supports are free from rub-
ber mount studs.

529 035 829

A35C25A

2

1

PTO ENGINE SUPPORT LIFTED

1. Engine support
2. Rubber mount stud

Remove PTO engine support.

A35C26A

1

2

PTO ENGINE SUPPORT REMOVAL

1. Remove
2. PTO engine support

Detach oil pump cable from oil pump.

Unplug oil outlet hose.

Unplug diaphragm fuel pump pulse hose.

Unplug oil inlet hose.

30

mmr2005-115

Summary of Contents for 2005 MACH Z
























































































































































































































































































































































Reviews:

No comments