manualshive.com logo in svg

Ski-Doo 2005 MACH Z, Shop Manual, Page: 314 / 343

Share
Download
Ski-Doo 2005 MACH Z Shop Manual Download Page 314

Section 09 BODY/FRAME

Subsection 01 (BODY)

A35H0AA

Remove front bumper.

Installation

The installation is the reverse of removal proce-
dure.

BOTTOM PAN

Removal

Remove front bumper.

Using Supertanium™ drill bit (P/N 529 031 800),
drill all rivets retaining bottom pan.

Remove bottom pan.

Installation

The installation is the reverse of removal proce-
dure.

WINDSHIELD

Removal

To remove the windshield, open hood then pull the
bottom part of windshield until its pins come out
of rubber grommets.

Installation

The installation is the reverse of removal proce-
dure.

ACCESS PANEL

Removal

Open hood.

Remove windshield.

Remove retaining screws, one on each sides.

A35H0BA

2

1

1. Access panel screws
2. Rubber grommet for windshield

Installation

The installation is the reverse of removal proce-
dure.

INDICATOR PANEL

Removal

Open hood and remove the access panel.

Remove the indicator panel screws.

A35H0CA

1

1

1. Indicator panel screws

Lift indicator panel and unplug all connectors.

Installation

The installation is the reverse of removal proce-
dure.

306

mmr2005-143

Summary of Contents for 2005 MACH Z
























































































































































































































































































































































Reviews:

No comments