Ski-Doo 2005 MACH Z Page 53 Shop Manual Download

Page: 53 / 343

Section 02 ENGINE

Subsection 04 (ENGINE REMOVAL AND INSTALLATION)

A35C21A

THROTTLE BODY REMOVAL

1. Clamps
2. Throttle body

Unplug fuel filter line from fuel rail.

Unscrew and remove fuel rail from engine.

A35C1YA

FUEL RAIL REMOVAL

1. Screws
2. Fuel rail

Unplug injectors and remove fuel rail from plastic
retaining plate.

Put fuel rail aside.

CAUTION:

Take care not to damage fuel injec-

tors.

A35C22A

FUEL RAIL DISASSEMBLY

1. Fuel rail
2. Plastic retainer plate

Unscrew E-RAVE actuator from frame.

Unplug connector and put E-RAVE actuator on top
of engine.

A35C23A

E-RAVE ACTUATOR REMOVAL

1. E-RAVE actuator
2. Unscrew
3. Connector

Remove LH engine support nuts.

mmr2005-115

Summary of Contents for 2005 MACH Z
























































































































































































































































































































































Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands

Ski-Doo 2005 MACH Z, Shop Manual

Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands