Ski-Doo 2005 MACH Z Page 248 Shop Manual Download

Page: 248 / 343

Section 06 DRIVE SYSTEM

Subsection 07 (DRIVE AXLE)

A33D0MA

TYPICAL

1. Pipe

MACH Z Models

A33D1UA

MEASURE FROM END OF DRIVE SHAFT

A. 48.3 mm (1.902 in)
B. 150.8 mm (5.937 in)
C. 273.8 mm (10.780 in)
D. 376.3 mm (14.815 in)

Summit Highmark and Summit
Highmark X Models

A33D1VA

MEASURE FROM END OF DRIVE SHAFT

A. 132.2 mm (5.205 in)
B. 178.1 mm (7.0118 in)
C. 310.4 mm (12.220 in)

Ensure to align indexing marks of each sprocket
when assembling.

A24D05A

TYPICAL

1. Indexing marks aligned

Bearing Protector

At assembly, flat side of bearing protector

no. 8

must be against bearing

no. 9

Bearing

Always push bearing

no. 9

by inner race.

mmr2005-137

237

Summary of Contents for 2005 MACH Z
























































































































































































































































































































































Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands

Ski-Doo 2005 MACH Z, Shop Manual

Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands