Ski-Doo 2005 MACH Z Page 232 Shop Manual Download

Page: 232 / 343

Section 06 DRIVE SYSTEM

Subsection 05 (BRAKE)

A35D06A

1. Pad pins

Remove pad spring

no. 11

A35D07A

1. Pad spring

Remove brake pads

no. 12

from caliper.

Installation

Clean pistons then push them inward before in-
stalling new brake pads.

Install brake pads and all other removed parts.

The brake disc

no. 13

must be centered in caliper.

Apply brake then check for proper brake disc po-
sitioning.

Push on appropriate caliper piston in order to
move pad inward allowing proper brake disc po-
sitioning.

A03D2KA

TYPICAL

1. Brake disc not centered
2. Brake disc centered
3. Apply brake before checking

Apply brake then recheck.

CALIPER

Removal

Drain brake system.

Unscrew Banjo bolt

no. 14

and discard sealing

rings

no. 15

Align brake disc slots with caliper bolts

no. 16

then

unscrew them.

mmr2005-135

219

Summary of Contents for 2005 MACH Z
























































































































































































































































































































































Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands

Ski-Doo 2005 MACH Z, Shop Manual

Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands