Ski-Doo 2005 MACH Z Page 277 Shop Manual Download

Page: 277 / 343

Section 07 REAR SUSPENSION

Subsection 02 (SC 4 SUSPENSION)

Make sure it is attached through proper hole from
the end.

Torque nut to 11 N•m (97 lbf•

A32F3DA

TYPICAL

1. 1

hole

2. 2

hole

A. 11 N•m (97 lbf•

)

SUSPENSION REMOVAL

Lift rear of vehicle and support it off the ground.

Completely loosen track tension.

Remove rear arm top axle screws.

Remove front arm top bolts.

A35F01D

TYPICAL

1. Remove rear arm top axle screws
2. Remove front arm top bolts

Lift rear of vehicle until front arm as enough clear-
ance to pass underneath tunnel.

A33F5VA

1. Enough clearance

A33F5WA

REMOVE SUSPENSION

SUSPENSION INSTALLATION

Installation is reverse of removal procedure. Pay
attention to the following details.

Inspect track thoroughly before reinstalling sus-
pension. Refer to TRACK.

Install suspension into track with front portion
first.

Adjust track tension.

RIDE ADJUSTMENT

Refer to the appropriate

Operator’s Guide

266

mmr2005-139

Summary of Contents for 2005 MACH Z
























































































































































































































































































































































Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands

Ski-Doo 2005 MACH Z, Shop Manual

Search results

Summary of Contents for 2005 MACH Z

Reviews:

Related manuals for 2005 MACH Z

Brands by name

Popular brands