SimonsVoss 3061 DM Manual Download | Manualshive

Page: 27 / 72

background image

Manual
Door Monitoring Cylinder

27 / 72

SimonsVoss

2 | Initial operation

15. Change the type of config device to WaveNet node in the

'Programming device' section, so that programming tasks are
implemented on the network

16. Click on [Apply] and [Finish] to proceed

ð

The network is now set up ready for use

ð

Programming tasks are now performed via the WaveNet node

Collective tasks

You can programme several locking devices at the same time using
'Collective tasks'

1.

Click on 'Network' and select 'Collective tasks' » 'WaveNet node'

2.

Highlight the components which are to be programmed

3.

Click on [Configure automatically]

ð

The programming tasks are distributed via the network

Forward status change

The forwarding of status changes must be activated for locking
devices

1.

Click on 'Network' in the menu and select 'Administer WaveNet'

2.

Select the network segment with the locking device in Segment
administration

3.

Highlight the locking device and open [Properties]

«
...
25
26
27
28
29
...
»

Summary of Contents for 3061 DM









































































Reviews:

No comments

Related manuals for 3061 DM

Brand: Assa Abloy Pages: 2

Shared Use RFID Camlock

Brand: Digilock Pages: 2

Brand: Sanela Pages: 7

Brand: Allegion Pages: 13

Lockwood 3579 Series

Brand: Assa Abloy Pages: 2

Brand: PBB Pages: 2

Brand: Samsung Pages: 24

Brand: Baby Lock Pages: 16

Brand: ABH Pages: 2

Brand: Dormakaba Pages: 50

Brand: DynaLock Pages: 16

Brand: G-U Pages: 148

Saflok QuantumII MT RFID

Brand: Kaba Pages: 8

Brand: Roger Pages: 2

Brand: Rittal Pages: 16

Brand: Rittal Pages: 16

Safelock Series

Brand: Weiser Pages: 2

Classic CCOM 611-02

Brand: SSS Siedle Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands