Silicon Graphics TP900 User Manual Download Page 48 | Manualshive

Page: 48 / 72

background image

32

007-4428-003

3: Replacing Modules

Pre-installation Safety Precautions

Observe the following safety precautions.

Warning:

Hazardous voltage and current levels are present inside the storage

subsystem. The replacement of rear-bay modules should be performed only by
technically qualified personnel.

Caution:

Do not remove a module unless a replacement can be immediately added. The

system must not be run without all modules in place.

Caution:

Follow electrostatic discharge (ESD) precautions while replacing the plug-in

modules. Avoid contact with the backplane components and module connectors.

Dealing with Hardware Faults

Ensure that you have obtained a replacement module of the same type before removing
any faulty module.

Caution:

If the SGI TP900 subsystem is powered on and you remove any module,

replace it immediately. If the subsystem is used without its modules or blanking plates
for more than a few minutes, the enclosure can overheat, causing power failure and data
loss. Such use will invalidate the warranty.

Continuous Operation during Replacement

If the enclosure contains two power supply modules, one of them can maintain power to
the subsystem while the other is replaced. A cooling module can be replaced without
SCSI data flow interruption. I/O modules can be replaced with the system powered up,
but the SCSI Channel will be down and data flow will be interrupted.

«
...
46
47
48
49
50
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Brand: Quantum Pages: 9

Brand: Quantum Pages: 2

Brand: Quantum Pages: 11

Brand: Quantum Pages: 7

Brand: Quantum Pages: 10

Brand: Quantum Pages: 8

Brand: Tandberg Data Pages: 58

ValueLoader DLT VS80

Brand: Quantum Pages: 50

Spinpiont HD320KJ

Brand: Samsung Pages: 1

Brand: StarTech.com Pages: 8

EASY ROLL 170.S/2/PS

Brand: garofalo Pages: 12

Brand: Macally Pages: 37

Brand: Arrow Storage Products Pages: 34

Brand: IBM Pages: 2

SiliconEdge Blue Series

Brand: Western Digital Pages: 2

Brand: Tuff Nano Pages: 17

Solaris Cluster 3.3 with StorageTek RAID Arrays

Brand: Oracle Pages: 30

Brand: Oracle Pages: 176

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands