Silicon Graphics TP900 User Manual Download Page 70 | Manualshive

Page: 70 / 72

background image

54

007-4428-003

B: Regulatory Information

Shielded Cables

The SGI TP900 storage system is FCC-compliant under test conditions that include the
use of shielded cables between the storage system and a host. Shielded cables reduce the
possibility of interference with radio, television, and other devices. If you use any cables
that are not from SGI, make sure they are shielded. Telephone cables do not need to be
shielded.

Electrostatic Discharge

SGI designs and tests its products to be immune to the effects of electrostatic discharge
(ESD). ESD is a source of electromagnetic interference and can cause problems ranging
from data errors and lockups to permanent component damage.

While operating the SGI TP900 storage system, it is important that you keep all the
covers, doors, and dummy (filler) panels in place. The shielded cables that came with the
product should be installed correctly.

Electromagnetic Emissions

This device complies with the Class B limits of Part 15 of the FCC Rules. Operation is
subject to the following two conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received, including interference that may
cause undesired operation.

Also, this device complies with Class B electromagnetic emissions limits of C.I.S.P.R.
Publication 22, Limits and Methods of Measurement of Radio Interference
Characteristics of Information Technology Equipment.

«
...
68
69
70
71
72
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Brand: U-Line Pages: 3

Brand: trueCall Pages: 16

Colonial Pinehurst

Brand: Little Cottage Pages: 19

Brand: Microdia Pages: 1

Brand: Western Digital Pages: 12

Brand: Yardmaster Pages: 23

AP-SRFD255AXXXXR-G

Brand: Apacer Technology Pages: 18

Brand: Medion Pages: 37

NetShare GX ME-752GNS

Brand: welland Pages: 3

220-420LTO - QUICK

Brand: TANDBERG Pages: 8

Brand: Argus Pages: 1

Memorator Pro 5xHS

Brand: Kvaser Pages: 27

Brand: Actidata Pages: 8

TS-269L TurboNAS

Brand: QNAP Pages: 6

DURAMAX 6 Ft WoodSide

Brand: USP Pages: 30

Brand: Rubbermaid Pages: 14

Brand: Rubbermaid Pages: 40

caviar blue xl500s

Brand: Western Digital Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands