Silicon Graphics TP900 User Manual Download Page 17 | Manualshive

Page: 17 / 72

background image

007-4428-003

1

Chapter 1

1.

Storage System Features

The SGI TP900 is a 2U-high 8-drive storage system that provides compact, high-capacity,
high-availability JBOD (“just a bunch of disks”) storage for supported SGI servers. The
enclosure backplane connects the 8 drives on one SCSI bus. As an option, the storage
system can also be configured on two SCSI busses (two strings of 4 drives). The SGI
TP900 is rack-mountable and is designed to use SCSI Parallel Interface 3 (SPI-3) capable
Low Profile (1-inch high) 3.5-inch disk drives. The drive carriers accept SGI-qualified
10,000 or 15,000 rpm U160/U320 SCSI disk drives.

This chapter gives information on the basic features of the SGI TP900 SCSI storage
system in the following sections:

•

“Enclosure Chassis” on page 2

•

“Front Panel LEDs” on page 4

•

“Plug-in Modules” on page 5

•

“Storage System Bay Numbering Convention” on page 17

«
...
15
16
17
18
19
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

DSN-4100 Series

Brand: D-Link Pages: 2

Mobile Ultra Memory Stick Micro

Brand: SanDisk Pages: 1

Z-DRIVE R2 M84 512GB PCI-EXPRESS SSD

Brand: OCZ Pages: 2

So Mobile SuperSpeed

Brand: DANE-ELEC Pages: 1

System Storage EXN2000

Brand: IBM Pages: 14

Brand: FAST LTA Pages: 8

Momentus ST9120827AS

Brand: Seagate Pages: 56

Brand: ClosetMaid Pages: 11

Brand: VME Pages: 2

Brand: Swissbit Pages: 11

Feronia 00108066

Brand: Hama Pages: 8

Brand: Yardmaster Pages: 24

Brand: Clickfree Pages: 76

Brand: Edsal Pages: 2

WD SATA Hard Drives

Brand: Western Digital Pages: 27

Brand: Salsbury Industries Pages: 5

XORAYA DATACUBE-N3

Brand: X2E Pages: 22

DURAMAX 6 Ft WoodSide

Brand: USP Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands