Silicon Graphics TP900 User Manual Download Page 59

Page: 59 / 72

Overview

007-4428-003

Table 4-1 summarizes the functions of the LEDs on the ESI/Ops panel and refers to the
sections that cover specific component failures.

The following sections explain how to troubleshoot initial startup problems, system
faults, power supply faults, and cooling module faults.

Table 4-1

ESI/Ops LED States

LED

LED State and Meaning

See This Section

System
status

Green signifies that power is applied to the enclosure.
Amber signifies that the ESI processor has failed.

“System Faults”
on page 45

Power
status

Green signifies that the power supplies are functioning normally.
Amber signifies that there is a PSU failure in a dual-PSU enclosure.
In the event of a PSU failure in a single-PSU enclosure, all LEDs are off.

“Power Supply
Faults” on
page 45

Cooling
status

Green signifies that all fans are functioning normally.
Amber signifies that there is a fan failure.

“Cooling
Module Faults”
on page 46

Summary of Contents for TP900









































































Search results

Summary of Contents for TP900

Reviews:

Related manuals for TP900

Brands by name

Popular brands

Silicon Graphics TP900, User Manual

Search results

Summary of Contents for TP900

Reviews:

Related manuals for TP900

Brands by name

Popular brands