Silicon Graphics TP900 User Manual Download Page 20 | Manualshive

Page: 20 / 72

background image

4

007-4428-003

1: Storage System Features

Front Panel LEDs

The Enclosure System Interface/Operators (ESI/Ops) panel consists of three status
indicator LEDs that are located on the front of the enclosure. The ESI/Ops panel provides
the enclosure with a micro controller that is used to monitor and control all elements of
the enclosure. Each element (system, power, and cooling status) is interfaced to the
processor. Figure 1-4 shows the ESI/Ops panel.

Figure 1-4

ESI/Ops Panel

Table 1-1 summarizes the functions of the LEDs on the ESI/Ops panel. See Chapter 4 for
descriptions of common problems, with possible solutions, that can occur with your SGI
TP900 system.

Table 1-1

ESI/Ops LED States

LED

LED State and Meaning

System status

Green signifies that power is applied to the enclosure.
Amber signifies that the ESI processor has failed.

Power status

Green signifies that the power supplies are functioning normally.
Amber signifies that there is a PSU failure in a dual-PSU enclosure.
In the event of a PSU failure in a single-PSU enclosure, all LEDs are off.

Cooling status

Green signifies that all fans are functioning normally.
Amber signifies that there is a fan failure.

System status

Cooling status

Power status

«
...
18
19
20
21
22
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Brand: Park Tool Pages: 2

A16F-R2431 Galaxy Raid

Brand: Rorke Data Pages: 110

Brand: QNAP Pages: 49

Brand: Olixir Pages: 2

Brand: Spectra Logic Pages: 15

Brand: ADDC Pages: 26

Brand: Samsung Pages: 35

Deskstar T7K500

Brand: Hitachi Pages: 2

DKC-F710I-1R6FM

Brand: Hitachi Pages: 3

Brand: Hitachi Pages: 6

Brand: Hitachi Pages: 1

Brand: Hitachi Pages: 1

External USB Storage

Brand: Hitachi Pages: 12

Brand: Hitachi Pages: 1

Brand: Hitachi Pages: 25

Endurastar J4K30

Brand: Hitachi Pages: 2

Endurastar J4K50

Brand: Hitachi Pages: 2

Brand: Hitachi Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands