Silicon Graphics TP900 User Manual Download Page 14 | Manualshive

Page: 14 / 72

background image

xiv

007-4428-003

About This Guide

Audience

This guide is written for owners and users of the SGI TP900 SCSI storage system. It
presumes general knowledge of SCSI technology and knowledge of the host SGI server,
the HBA, and other SCSI devices to which the storage system might be cabled.

Related Publications

Besides this manual and the manuals for the storage system third-party software, you
should locate the latest versions of the user’s guide for the servers. If you do not have
these guides, you can find the information online in the following locations:

•

IRIS InSight Library. From the Toolchest, select

Help

>

Online Books

>

SGI EndUser

or

SGI Admin

, and select the applicable owner’s or hardware guide.

•

Technical Publications Library. If you have access to the Internet, see the following
URL:

http://techpubs.sgi.com/library/

Product Support

SGI provides a comprehensive product support and maintenance program for its
products:

•

If you are in North America and want support for your SGI-supported products,
contact the Technical Assistance Center at 1-800-800-4SGI or your authorized
service provider.

•

If you are outside North America, contact the SGI subsidiary or authorized
distributor in your country.

Reader Comments

If you have comments about the technical accuracy, content, or organization of this
document, contact SGI. Be sure to include the title and document number of the manual
with your comments. (Online, the document number is located in the front matter section

«
...
12
13
14
15
16
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Brand: Tab Pages: 26

Brand: IBM Pages: 122

Momentus ST320LM010

Brand: Seagate Pages: 33

Brand: 7-BIT Pages: 8

220-420LTO - QUICK

Brand: TANDBERG Pages: 8

Brand: Cisco Pages: 23

Brand: Cisco Pages: 75

Brand: Cisco Pages: 132

Brand: Cisco Pages: 58

UCS 6400 Series

Brand: Cisco Pages: 68

Smart Storage NSS322

Brand: Cisco Pages: 2

Brand: Maxtor Pages: 2

Brand: Toshiba Pages: 1

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 1

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands