Silicon Graphics TP900 User Manual Download Page 30 | Manualshive

Page: 30 / 72

background image

14

007-4428-003

1: Storage System Features

Figure 1-14 shows a U160 loopback module.

Figure 1-14

1 x 8 configuration U160 Loopback Module

Cooling Module

One cooling plug-in module is mounted in the rear of the system. Optionally, a second
cooling module can be fitted to provide greater redundancy. The cooling modules
connect to the backplane for power and status signal connections. The modules pull air
from a plenum behind the drive backplane and exhaust the warm air at the rear of the
enclosure. Figure 1-15 shows a cooling module.

«
...
28
29
30
31
32
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Express5800/R120f-2E

Brand: NEC Pages: 36

Brand: IBM Pages: 102

Brand: Accordance Systems Pages: 22

Brand: 7-BIT Pages: 4

Brand: G-Technology Pages: 33

DDS Generation 6 USB

Brand: IBM Pages: 11

5BIG THUNDERBOLT 2

Brand: LaCie Pages: 20

Brand: Seagate Pages: 48

Brand: Samsung Pages: 17

Brand: Samsung Pages: 18

Brand: Samsung Pages: 1

HD080HJ - 80 GB Hard Drive

Brand: Samsung Pages: 1

HD080HJ - 80 GB Hard Drive

Brand: Samsung Pages: 2

Brand: Samsung Pages: 27

HARD DISK DRIVE

Brand: Samsung Pages: 34

SO MOBILE OTB HELLO KITTY

Brand: DANE-ELEC Pages: 2

Brand: Supatool Pages: 2

Brand: Fantec Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands