Silicon Graphics TP900 User Manual Download Page 53 | Manualshive

Page: 53 / 72

background image

Replacing Drive Carrier Modules

007-4428-003

37

Replacing Drive Carrier Modules

Caution:

Follow electrostatic discharge (ESD) precautions while replacing the drive

carriers. Avoid contact with the backplane components and module connectors.

Follow these steps to remove and replace a drive carrier module from the SGI TP900
enclosure:

Caution:

Do not remove a drive carrier unless a replacement or a dummy carrier can be

immediately added. The system must not be run without all modules in place. Any
unused drive bays must be fitted with a dummy carrier module.

1.

Spin down the drive prior to removal, using the operating system.

Caution:

Damage can occur to a drive if it is removed while still spinning. If you

cannot use the operating system to spin down the drives prior to removal, perform
all steps of the following procedure to ensure that the drive has stopped prior to
removal.

2. Release the carrier handle by pressing the latch in the handle towards the right.

Note:

The anti-tamper lock must be off. See “Engaging the Anti-tamper Locks” on

page 28 for instructions on disengaging the anti-tamper lock.

3. Gently withdraw the drive carrier module approximately 1 inch (25mm), and then

wait 30 seconds.

4. Withdraw the module from the drive bay.

«
...
51
52
53
54
55
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

FlashSystem 710

Brand: IBM Pages: 46

Brand: IBM Pages: 8

Brand: IBM Pages: 202

DARA-206000 - Travelstar 12 GB Hard Drive

Brand: IBM Pages: 206

BladeCenter S 7779

Brand: IBM Pages: 28

Brand: Quantum Pages: 68

DLTtape SDLT 600

Brand: Quantum Pages: 142

Brand: Quantum Pages: 16

Brand: Quantum Pages: 8

StorNext QD7000

Brand: Quantum Pages: 17

Brand: Tandberg Data Pages: 81

StorNext QD7000

Brand: Quantum Pages: 39

Brand: Quantum Pages: 98

Brand: Quantum Pages: 12

Brand: Quantum Pages: 2

Brand: Qualstar Pages: 366

Brand: Qualstar Pages: 42

Brand: Qualstar Pages: 177

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands