Silicon Graphics TP900 User Manual Download Page 35 | Manualshive

Page: 35 / 72

background image

007-4428-003

19

Chapter 2

2.

Setup and Operation

This chapter describes how to set up and operate your SGI TP900 storage system in the
following sections:

•

“Unpacking and Inspecting the Storage System” on page 19

•

“Connecting the Power Cord” on page 20

•

“Attaching Interface Cables” on page 21

•

“SCSI_ID Addressing” on page 24

•

“Powering On the Enclosure” on page 26

•

“Powering Off the Enclosure” on page 27

•

“Engaging the Anti-tamper Locks” on page 28

Note:

If you use an LSI1030 (LSI22320-R) HBA, you must upgrade the drive firmware

from revision 2741 to revision 2743 in order to have the full benefit of U320 disk drive
speed. The firmware upgrade is normally performed by an SGI service engineer.

Unpacking and Inspecting the Storage System

Remove the storage system from the packaging container and check that all accessories
are included. Inspect the packaging container for evidence of mishandling during transit.
If the packaging container is damaged, photograph it for reference. After removing the
contents, keep the damaged container and the packing materials.

Inspect the storage system and accessories for damage. If the contents appear damaged,
file a damage claim with the carrier immediately. For installations under U.S. auspices,
notify the Customer Support Call Center (CSCC) for any missing, incorrect, or damaged
items. Elsewhere, follow local policies.

«
...
33
34
35
36
37
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Brand: Seville Classics Pages: 2

Brand: U-Line Pages: 39

Brand: Dell EMC Pages: 70

Brand: VME Pages: 2

Brand: Kikusui Pages: 6

Brand: Huawei Pages: 8

OceanStor 18000F V5 Series

Brand: Huawei Pages: 29

Brand: Huawei Pages: 11

Brand: Huawei Pages: 14

Quidway S5000 Series

Brand: Huawei Pages: 68

FusionModule1000A

Brand: Huawei Pages: 108

OceanStor VIS6300

Brand: Huawei Pages: 42

Brand: Huawei Pages: 11

OceanStor 18500 V5

Brand: Huawei Pages: 17

Brand: Huawei Pages: 22

Brand: Huawei Pages: 173

OceanStor 18000 V3 Series

Brand: Huawei Pages: 196

Brand: Huawei Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands