Silicon Graphics TP900 User Manual Download Page 24 | Manualshive

Page: 24 / 72

background image

8

007-4428-003

1: Storage System Features

Anti-tamper Locks

Anti-tamper locks are fitted in the drive carrier handles and are accessed through the
small cutout in the latch section of the handle. These are provided to disable the normal
“pinch” latch action of the carrier handle. See “Engaging the Anti-tamper Locks” on
page 28 for instructions on how to engage or disengage the anti-tamper lock. Figure 1-7
shows the location of the anti-tamper locks.

Note:

The drives will operate with the locks either engaged or disengaged.

Figure 1-7

Anti-tamper Locks

Anti-tamper lock

Anti-tamper lock

«
...
22
23
24
25
26
...
»

Summary of Contents for TP900









































































Reviews:

No comments

Related manuals for TP900

Brand: Quantum Pages: 384

Brand: Tandberg Data Pages: 60

RS-1600-FC-FFX2

Brand: Xyratex Pages: 82

Brand: Hama Pages: 4

Brand: B&B Electronics Pages: 2

Brand: KROFTMAN Pages: 31

Brand: KEHUA TECH Pages: 51

Brand: Raidon Pages: 2

StorageScaler 2460

Brand: DataDirect Networks Pages: 46

Brand: DataDirect Networks Pages: 106

Brand: TrekStor Pages: 48

Brand: morse Pages: 6

Microdrive RHMD2G

Brand: Sony Pages: 2

Memory Stick PRO DUO MSX-M256S

Brand: Sony Pages: 2

Memory Stick MSA-32A

Brand: Sony Pages: 2

Memory Card DKA-MC10F

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands