67
Siemens Building Technologies
Fire Safety & Security Products
08.2006
Operation User
action
Notes
Recall Preset
[PP ENTER] n [PP ENTER]
Range 1-99. Preset 95* or Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command. When in OSD mode
Preset 1 switches the joystick between cursor and camera control.
When in OSD cursor mode Preset 3 operates as SET.
Start Preset Sequence
[A/P]
Autopan function starts tour. Autopan indicator will not be lit
however.
Save Preset
[PROG] [PP ENTER] [n] [PP ENTER] Range 1-99. [PROG] is switch on rear of keyboard.
Enter OSD Menu Mode
[PP ENTER] [9]* [5]* [PP ENTER] or
[2]* [PPENTER] [2]* [PP ENTER]
within 2 seconds.
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode ‘MENU’ command.
Navigate OSD Menu Mode Joystick for Up/Down/Left/Right. [PP
ENTER] [1] [PP ENTER] to toggle
between cursor and camera control.
[PP ENTER] [3][PP ENTER] for Set.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET.
* The presets used to access the OSD are programmable via the XTU.
12.5.7 Philips
protocol
NOTE
RS485 connection; 9600 baud, no parity, 8 data bits, 1 stop bit.
Tested using Forward Vision Philips CamSet simulator V6. (NB - some bugs in this simulator prevent
complete testing, e.g. it is not possible to set a camera address above 256, also it is not possible to
pan and tilt at the same time. However it is believed the XTU software will operate correctly).
Operation User
action
Notes
Set Camera Address
[n] [SET CAMERA ADDRESS]
Addresses 1-512 supported (simulator will only support 1-256).
Pan / Tilt / Zoom / Focus
[LEFT] / [RIGHT] / [UP] / [DOWN] /
[ZOOM IN] / [ZOOM OUT] / [FOCUS
NEAR] / [FOCUS FAR]
Opcodes 2 (fixed speed), 4, 5 and 8 (timed command) supported for
P/T/Z/F. Opcode 6 (timed command) supported for Z/F. When in
OSD cursor mode Pan / Tilt operate as cursor right / left / up / down
(but see also Recall Preset 1 below).
Iris
[IRIS OPEN] / [IRIS CLOSE]
Only operates when exposure priority is set to KEYBOARD and
when Man Exp is on.
AutoIris
[Man Exp]
If off this will override manual iris control.
AutoFocus On
[MAN FOCUS] off
AutoFocus Off
[MAN FOCUS] on
Night Mode
[IR] on
Switches camera to night mode (external version only)
Day Mode
[IR] off
Switches camera to day mode (external version only)
One-Touch White Balance
[Iris Close]
If one-touch white balance is enabled in OSD and exposure priority
is not set to KEYBOARD.
Recall Preset
[n] [SHOT]
Range 1-10 (in simulator, 1-99 supported). Preset m* or Preset 2*
twice within 2 seconds functions as the OSD Mode ‘MENU’
command. When in OSD mode Preset 1 switches the joystick
between cursor and camera control. When in OSD cursor mode
Preset 3 operates as SET.
Start Preset Tour
[START TOUR]
Save Preset
[n] [SET]
Range 1-10 (in simulator, 1-99 supported)
Enter OSD Menu Mode
[m]* [SHOT] or [2]* [SHOT] [2]*
[SHOT] within 2 seconds
Recall Preset m* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode ‘MENU’ command.
Navigate OSD Menu Mode Joystick for Up/Down/Left/Right.[1]
[SHOT] to toggle between cursor and
camera control.[3] [SHOT] for Set.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET.
* The presets used to access the OSD are programmable via the XTU.
Summary of Contents for Solaris CCDS1415-DN
Page 73: ......