61
Siemens Building Technologies
Fire Safety & Security Products
08.2006
Alarms
When using Molynx V3 protocol in conjunction with a V3i telemetry matrix it is
possible to send alarms back over the telemetry link. It is necessary to configure
the V3i to have bi-directional telemetry on the channel being used and for the
appropriate camera alarms to be enabled. Also, on the Solaris™, the alarms must
be configured to have Remote Reporting enabled.
Only the tamper and alarms 1-6 may be sent back, alarm 7 is not usable in this
way. The mapping is such that the tamper is the first alarm in the block of 8 camera
alarms, followed by alarms 1-6.
With a controller other than a V3i it is not possible to use bi-directional telemetry
hence remote reporting of alarms is not available. Use normal Molynx - not Molynx
V3 - telemetry in these instances.
12.4.2 PCCON, PCCON 1-way and PCCON MULTIDROP
NOTE
RS485 connection; 9600 baud, even parity, 8 data bits, 1 stop bit.
Tested using a PC running Hyperterminal with direct connection to serial port
Operation User
command
Notes
Return Status
@1
Returns camera number and latched functions status.
Select Camera
@3, n
(Multidrop only)
Selects camera n as the current camera, disabling all others.
Camera Function On
@5, n
Home (n=1), Pan Right (2), Pan Left (3), Tilt Up (4), Tilt Down (5),
Zoom In (6), Zoom Out (7), Focus Far (8), Focus Near (9), Iris Close
[10], iris Open [11], AutoIris [20], LensSlow (22), AutoFocus (23) are
implemented. Also Lamps (21) switches the unit from day to night
mode (colour/mono version only).When in OSD mode (and only
after OSD mode is accessed using a preset as detailed below)
Pan/Tilt commands from the controller are sent as Camera Setup
commands RIGHT/LEFT/UP/DOWN (but see also Recall Preset 1
below).
Camera Function Off
@6, n
Pan Right (n=2), Pan Left (3), Tilt Up (4), Tilt Down (5), Zoom In (6),
Zoom Out (7), Focus Far (8), Focus Near (9), LensSlow (22),
AutoFocus (23) are implemented. Also Lamps (21) switches the unit
from night to day mode (colour/mono version only).When in OSD
mode (and only after OSD mode is accessed using a preset as
detailed under Recall Preset below) Pan/Tilt commands from the
controller are sent as Camera Setup commands
RIGHT/LEFT/UP/DOWN (but see also Recall Preset 1 below).
P/T Speed
@7, p, t
0 to 100% for each.
Recall Preset
@8, n
Range 1-99 (not 95). Recall Preset 95* or Recall Preset 2* twice
within 2 seconds sends the Camera Setup Mode 'MENU' command.
When in OSD mode Recall Preset 1 toggles between sending
Pan/Tilt commands as PAN/TILT and sending them as CURSOR
RIGHT/LEFT/UP/DOWN. When in OSD mode Recall Preset 3
sends the SET command.
Program Preset
@9, n
Range 1-99.
Preset Sequence Recall
@10
Preset Sequence Program
@11, n, p1 … pn, d
2-16 (n) positions. Sets sequence/tour positions (p1…pn) (range 1-
99) and dwell time (d) (range 1-255s).
Preset Tour Recall
@12
Preset Tour Program
@13, s1, …, s16, d1, …, d16
Programs tour speeds and dwells (16 of each). Presets are the
same as those programmed with the Preset Sequence Program
command. Values are ignored for unused positions.
Variable Speed Preset Recall
@16, p, s
Preset range 1-99; speed range 1-100%.
Relay Status
@26, 1
Return relay status (must be relay 1). 0=open, 1=closed
Relay Control
@27,1,f
Operate relay (f=0 to turn off, f=1 to turn off). Must be relay 1.
Summary of Contents for Solaris CCDS1415-DN
Page 73: ......