64
Siemens Building Technologies
Fire Safety & Security Products
08.2006
Operation User
action
Notes
is not set to KEYBOARD.
Recall Preset
[n] [PRESET]
Range 1-89.Preset 95* or Preset 2* twice within 2 seconds functions
as the OSD Mode 'MENU' command. When in OSD mode Preset 1
switches the joystick between cursor and camera control. When in
OSD cursor mode Preset 3 operates as SET.
Store Preset
[n] hold [PRESET]
Range 1-89.
Run Pattern
[PATTERN]
Enter OSD Menu Mode
[9] [5] [PRESET] or [2]
[PRESET] [2] [PRESET] within
2 seconds.
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
Navigate OSD Menu Mode
Joystick for
Up/Down/Left/Right.[3]
[PRESET] for Set.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET
* The presets used to access the OSD are programmable via the XTU.
12.5.2 Ernitec ERNA protocol
NOTE
RS485 connection; 2400 baud, no parity, 8 data bits, 1 stop bit.
Camera addressing is 0-254 for cameras 1-255. Also responds to broadcast address 255.
Tested using Ernitec Keyboard 1503M.
Operation User
action
Notes
Pan / Tilt /Zoom / Focus
Joystick for Pan/Tilt/Zoom,[FN] / [FF]
for Focus
When in OSD cursor mode Pan / Tilt operate as cursor right / left /
up / down (but see also Recall Preset 1 below).
Iris
[OPEN] / [CLOSE]
Only operates when exposure priority is set to KEYBOARD.
AutoIris On
[AUTO] [OPEN] or [AUTO] [CLOSE]
Overridden automatically on a manual iris operation.
AutoFocus On
[AUTO] then either [FN] or [FF]
AutoFocus Off
[FN] or [FF]
Manual control overrides autofocus.
Night Mode
[4] [AUX ON]
Activates Auxiliary 4 function. Switches camera to night mode
(colour/mono version only).
Day Mode
[4] [AUX OFF]
Deactivates Auxiliary 4 function. Switches camera to day mode
(colour/mono version only).
One-Touch White Balance
[IC]
If one-touch white balance is enabled in OSD and exposure priority
is not set to KEYBOARD.
Recall Preset
[n] [PRESET]
Range 1-99. Preset 95* or Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command. When in OSD mode
Preset 1 switches the joystick between cursor and camera control.
When in OSD cursor mode Preset 3 operates as SET.
Start Preset Sequence
[PRESET SEQUENCE]
Starts Tour 1.
Save Preset
[n] [ESC] [PRESET]
Range 1-99.
Insert Preset into Stack
[n] [SHIFT]+[INS]
Appends specified preset to end of current tour if possible**. Speed
= 100%, Dwell = currently selected dwell.
Delete Preset from Stack
[n][SHIFT]+[DEL]
Deletes the last occurrence of the specified preset from the tour** (if
present) and moves the presets above it down by one position.
Leaves any other occurrences of the same preset in the tour intact.
Clear Stack
[ESC] [AUX OFF]
Clears the tour**.
Sequence Dwell Time
[n] [TIME]
Sets the dwell time used by the next Insert Preset into Stack
command*.
Enter OSD Menu Mode
[9] [5] [PRESET] or[2] [PRESET] [2]
[PRESET] within 2 seconds
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
Navigate OSD Menu Mode Joystick for Up/Down/Left/Right.[3]
[PRESET] for Set.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET.
* The presets used to access the OSD are programmable via the XTU.
** It is recommended that the OSD is used to setup a Tour.
Summary of Contents for Solaris CCDS1415-DN
Page 73: ......