manualshive.com logo in svg

Siemens SIPROTEC, Manual

The Siemens SIPROTEC is a cutting-edge product built to ensure reliable and secure power system protection. Offering unmatched precision and performance, this advanced device comes with a comprehensive user Manual that can be conveniently downloaded for free from our website manualshive.com. Explore the product's full potential with our detailed and easily accessible Manual.

Share
Download
background image

Functions

2.1 General

SIPROTEC, 7SD5, Manual

C53000-G1176-C169-5, Release date 02.2011

61

 

Note

When the addresses 

1116

 

RE/RL(Z1)

 and 

1118

 

RE/RL(> Z1)

 are set to about 2.0 or more, please keep in 

mind that the zone reach in R direction should not be set higher than the value determined previously (see 
Section 2.5.2.2/margin heading Resistance Tolerance). If this is not observed, it may happen that phase-to-
earth impedance loops are measured in an incorrect distance zone, which may lead to loss of tripping coordi-
nation in the case of earth faults with fault resistances.

 

Earth Impedance (Residual) Compensation with Magnitude and Angle (K

0

–Factor)

When the complex earth impedance (residual) compensation factor K

0

 is set, the addresses 

1120

 to 

1123

 

apply. In this case it is important that the line angle is set correctly (address 

1105

, see margin heading „General 

Line Data“) as the device needs the line angle to calculate the compensation components from the K

0

. These 

earth impedance compensation factors are defined with their magnitude and angle which may be calculated 
with the line data using the following equation:

Where

Z

0

= (complex) zero sequence impedance of the line

Z

1

= (complex) positive sequence impedance of the line

These values can be applied either to the entire line or as per unit of length values since the quotients are in-
dependent of length. Furthermore, it makes no difference whether the quotients are calculated with primary, or 
secondary values.

For overhead lines it is generally possible to calculate with scalar quantities as the angle of the zero sequence 
and positive sequence system only differ by an insignificant amount. With cables however, significant angle dif-
ferences may exist as illustrated by the following example.

Calculation Example:

110 kV single-conductor oil-filled cable 3 · 185 mm

2

 Cu with the following data

Z

1

/s

= 0.408 · e

j73°

 

Ω

/km positive sequence impedance

Z

0

/s

= 0.632 · e

j18.4°

 

Ω

/km zero sequence impedance

(where s 

= line length)

The calculation of the earth impedance (residual) compensation factor K

0

 results in:

The magnitude of K

0

 is therefore

Summary of Contents for SIPROTEC









































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIPROTEC

Zenith R50V26 Operating Manual preview
R50V26
Brand: Zenith Pages: 56
Zenith R56W36 Installation And Operating Manual preview
R56W36
Brand: Zenith Pages: 60
Zenith R45W47 Installation And Operating Manual preview
R45W47
Brand: Zenith Pages: 36
ALLTEC DynaShield ADS 2F Series User Manual And Installation Instruction preview
DynaShield ADS 2F Series
Brand: ALLTEC Pages: 12
Siemens Cerberus Pyrotronics CP2341 Installation Instructions preview
Cerberus Pyrotronics CP2341
Brand: Siemens Pages: 2
Siemens 6AV6881-0AJ21-0AA0 Product Information preview
6AV6881-0AJ21-0AA0
Brand: Siemens Pages: 2
Siemens 6SL3760-8CV00-0FA0 Assembly preview
6SL3760-8CV00-0FA0
Brand: Siemens Pages: 7
Siemens SIMATIC NET LP798-2N Compact Operating Instructions preview
SIMATIC NET LP798-2N
Brand: Siemens Pages: 32
Siemens 7SV512 Instruction Manual preview
7SV512
Brand: Siemens Pages: 136
Siemens 7UM515 Instruction Manual preview
7UM515
Brand: Siemens Pages: 232
Siemens 7SR242 Duobias Technical Manual preview
7SR242 Duobias
Brand: Siemens Pages: 382
Siemens Argus 7SR11 Manual preview
Argus 7SR11
Brand: Siemens Pages: 406
Siemens SIPROTEC 4 User Manual preview
SIPROTEC 4
Brand: Siemens Pages: 734
Kaya Safety Rock R-5 A User Manual preview
Rock R-5 A
Brand: Kaya Safety Pages: 7
Asco 457 Installation & Operation Manual preview
457
Brand: Asco Pages: 24
Taga PF-400USB Instruction Manual preview
PF-400USB
Brand: Taga Pages: 12
Palmer Safety H11110005 Instruction Manual preview
H11110005
Brand: Palmer Safety Pages: 20
Panasonic PT-61G53X Operating Instructions Manual preview
PT-61G53X
Brand: Panasonic Pages: 18

Brands by name

Popular brands

Load more brands