Siemens SIMOTICS CONNECT 400 Operating Instructions Manual Download

Page: 75 / 120

Note
Service factor and cooling method
• Service factor according to NEMA MG-1 (if applicable)
• Cooling method according to IEC60034-6

2. Check the data entered and confirm with the "Send" button.

3. Continue to commission the equipment.

6.3.4.8

Asset Info - Step 7/7

Note
Settings cannot be modified subsequently

Select the following settings carefully. There is no way of modifying the settings after selection.

If you choose an incorrect setting, repeat the onboarding process.

Commissioning

6.3 Commissioning with iOS

SIMOTICS CONNECT 400
Operating Instructions, 08/2021, A5E50161952B AE

Summary of Contents for SIMOTICS CONNECT 400

























































































































Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 400, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands