Siemens SIMOTICS CONNECT 400 Operating Instructions Manual Download

Page: 50 / 120

3. Select the operating point. If there are multiple parameter sets in the rating data, select the

parameter set that matches the connection conditions of your motor.

4. Select one of the following operating modes:

– Line operation - direct-on-line operation (DOL)

– Converter operation - variable speed drive operation (VSD)

Note

With the current firmware version 0.6.0, for motors in converter operation (VSD) in "SIDRIVE
IQ Fleet", no values are displayed for torque, electrical power consumption, and energy
consumption.

Commissioning
6.2 Commissioning with Android

SIMOTICS CONNECT 400

Operating Instructions, 08/2021, A5E50161952B AE

Summary of Contents for SIMOTICS CONNECT 400

























































































































Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 400, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands