Siemens SIMOTICS CONNECT 400 Operating Instructions Manual Download

Page: 36 / 120

6.2.4.5

Intervals - Step 4/7

In this step, you can define the intervals for measurements and data transfers. The remaining
battery life is recalculated based on your entry.

Note
Calculated battery life

The calculated battery life is a statistical value. The actual remaining battery life may differ
depending on temperature influences or the connection quality of the WLAN network.

Note
Effects that influence the battery life

Shorter intervals result in a shorter battery life.

The following intervals are preset in the factory:

• 5 minutes - interval for measuring temperature, vibrations, rotational frequency, operating

status
You can change these settings within a specified range.

• 15 minutes - interval for calculation of speed, torque and energy consumption

This setting is always three times the short measurement interval that has been set.

• 24 hours - interval for transmission of the stored data to "SIDRIVE IQ Fleet"

You can modify these settings within a preset range of 1 to 48 hours.

Commissioning
6.2 Commissioning with Android

SIMOTICS CONNECT 400

Operating Instructions, 08/2021, A5E50161952B AE

Summary of Contents for SIMOTICS CONNECT 400

























































































































Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 400, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands