Siemens SIMOTICS CONNECT 400 Operating Instructions Manual Download

Page: 86 / 120

Use the "Identification" function to check whether you are connected with the required
connectivity module.

Procedure

1. Open the "SIDRIVE IQ Config" application.

2. Open the overview page.

3. Select an asset from the "Visible" tab.

4. Tap on the motor symbol

in the list entry.

The connectivity module LED flashes. The firmware version is read out and displayed.

7.1.3

Changing measurement and synchronization intervals

The following intervals are preset in the factory:

• 5 minutes - interval for measuring temperature, vibrations, rotational frequency, operating

status
You can change these settings within a specified range.

• 15 minutes - interval for calculation of speed, torque and energy consumption

This setting is always three times the short measurement interval that has been set.

• 24 hours - interval for transmission of the stored data to SIDRIVE IQ Fleet

You can change these settings within a specified range of between 1 and 48 hours.

Note
Effects that influence the battery life

Shorter intervals result in a shorter battery life.

Operation
7.1 Operation with Android

SIMOTICS CONNECT 400

Operating Instructions, 08/2021, A5E50161952B AE

Summary of Contents for SIMOTICS CONNECT 400

























































































































Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands

Siemens SIMOTICS CONNECT 400, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS CONNECT 400

Reviews:

Related manuals for SIMOTICS CONNECT 400

Brands by name

Popular brands