Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 190

Page: 190 / 238

Service and maintenance

10.1 Error and diagnostics messages

SIMATIC MV500

190

Operating Instructions, 06/2018, C79000-G8976-C494-01

Table 10- 10 Diagnostic information of SFB 54 "RALRM" - "AINFO" parameter

Byte

Value

Meaning

0 ... 1

According to PNIO standard

Block type

2 ... 3

W#16#001A / W#16#0016

Length of the diagnostics data with an incoming / outgoing alarm.

4 ... 5

W#16#0100

Version (fixed)

6 ... 7

W#16#0001 / W#16#000C

ID for the alarm type: Diagnostics alarm incoming / diagnostics alarm

outgoing.

8 ... 11

DW#16#00000000

API (fixed)

12 ... 13

W#16#0000

Slot (fixed)

14 ... 15

W#16#0001

Subslot (fixed)

16 ... 19

DW#16#00000300

Module identification (fixed)

20 ... 23

DW#16#00000000

Submodule identification (fixed)

24 ... 25

W#16#Bxxx / W#16#xxx

Alarm specification for incoming / outgoing alarm:

•

Bits 0 to 10: Sequence number

•

Bit 11: Channel diagnostics: 0 (fixed)

•

Bit 12: Status of vendor-specific diagnostics

•

Bit 13: Status of diagnostics for submodule

•

Bit 14: Reserved: 0

•

Bit 15: Diagnostics status

26 ... 27

W#16#0004

ID for vendor-specific diagnostics (fixed).

28 ... 29

See value with the section "Error

messages (Page 176)"

ID of the error that occurred.

In addition to the event-related readout of the diagnostic data with the SFB 54, you also have

the option of reading out status-related diagnostics data.
You read out status-related diagnostics data using SFB 52 "RDREC".
Proceed as follows to call the SFB 52:
1.

Assign the diagnostic address of the optical reader in hexadecimal form to the "ID"

parameter.

Assign the value 2 to the "INDEX" parameter.

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands