Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 58

Page: 58 / 238

Network and system integration

4.6 System configuration with CM and RFID reader

SIMATIC MV500

Operating Instructions, 06/2018, C79000-G8976-C494-01

System characteristics

●

The result output of the optical reader takes place via the RS232 interface.

●

The optical reader is triggered either via digital I/O, RS232 or via the built-in auto-trigger

function.

●

A PC/programming device is connected via Ethernet to allow adjustment of the device.

4.6

System configuration with CM and RFID reader

①

Optical sensor or light barrier (for trigger signal)

②

Object with code

Figure 4-5

Example: System configuration of optical reader with RFID reader on a communication

module

System characteristics

●

In mixed operation with an RFID reader, e.g. from the SIMATIC RF300 series, the optical

reader can be connected to a communication module and operated.

●

Both the optical reader and the RFID reader are integrated in STEP 7 by the Ident profile

block.

●

A PC/programming device is connected via Ethernet to allow adjustment of the device.

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands