Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 161

Page: 161 / 238

Process interfacing via an automation system (PLC, PC)

9.7 Remote client

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

161

Characters

Description

Logical signal for linking.
If p3 = "4", the parameter has no significance.

•

ASCII characters with the value "0" to "5"
–

0: Logical signal "IN_OP"

–

1: Logical signal "TRD"

–

2: Logical signal "RDY"

–

3: Logical signal "READ"

–

4: Logical signal "MATCH"

–

5: Logical signal "NOK"

Reserved

The value must be "0" to retain upwards compatibility.

9.7

Remote client

The remote client interface is an HTTP-based interface. The remote client can trigger

functions using HTTP requests sent to the optical reader. To make this possible, you need to

configure an IP address in the WBM that corresponds to the address of the client. The

optical reader only processes the HTTP requests that have the configured IP address as the

sender.

9.7.1

XML backup and XML restore

Note
Do not control at the same time via the control interface
Ensure throughout the entire automation process that nothing is controlled via the control

interface while the XML Backup and XML Restore functions are running. If control is

performed via the control interface, by setting the DISA bit for example, the "XML Backup"

and "XML Restore" functions cannot be executed.

Note
Backing up the diagnostic images before execution of the "XML Backup" and "XML Restore"

functions
Executing the "XML Backup" and "XML Restore" functions may delete any diagnostics

images in the optical reader memory.
If required, save the diagnostic images before you execute one of these functions.

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands