Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 29

Page: 29 / 238

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

Image processing

3.1

Code reading (1D/2D codes)

3.1.1

Area of application and examples

The optical reader reads the types of code listed below.

Two-dimensional codes

●

DMC

●

PDF417

●

DotCode

One-dimensional codes

●

Codabar

●

Code 32

●

Code 39 (without checksum)

●

Code 39+CS (with checksum)

●

Code 93

●

Code 128

●

EAN 8

●

EAN 13

●

GS1 Databar Expanded

●

GS1 Databar Limited

●

GS1 Databar Omnidirectional

●

GS1 Databar Stacked

●

Int. 2/5 (without checksum)

●

Int. 2/5+CS (with checksum)

●

Pharmacode

●

Postnet

●

UPC-A

●

UPC-E

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands