Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 57

Page: 57 / 238

Network and system integration

4.5 System setup via the RS-232 interface

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

System characteristics

●

The result output of the optical reader takes place via the Ethernet interface.

●

The optical reader can be triggered via either:
–

Digital I/O

–

TCP/IP

–

The built-in auto-trigger function

●

A PC/programming device is connected via Ethernet and a switch to allow adjustment of

the device.

4.5

System setup via the RS-232 interface

①

Optical sensor or light barrier (for trigger signal)

②

Object with code

Figure 4-4

Example: System configuration via the RS232 interface

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands