Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 171

Page: 171 / 238

Process interfacing via an automation system (PLC, PC)

9.9 Example programs

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

171

Requirements

●

.NET Framework v4.0 must be installed to run the demo program.

●

The PC must be connected with the optical reader over the Ethernet interface.

Settings in WBM
Make the following settings in the WBM:

●

"Settings > Communication > Interfaces > Archiving/MMI" menu:
Enter the IP address and the port of the PC on which you want to archive the diagnostic

information.

●

"Settings > Communication > Use > Diagnostics transfer" menu:
Select from the drop-down lists which data you want to archive: Diagnostics data sets,

diagnostics images or both.

Operation of the example program

Start the example program by double-clicking "MMIDiagnosticsGUI.exe".

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands