Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 76

Page: 76 / 238

Connection

6.2 Power supply using Power over Ethernet (PoE)

SIMATIC MV500

Operating Instructions, 06/2018, C79000-G8976-C494-01

Only connect safety extra-low voltage (SELV) according to IEC 62368-1

WARNING

Operation with safety extra-low voltage
The device is designed for operation with safety extralow voltage (SELV). This means that

only safety extra-low voltages (SELV) according to IEC 62368-1 can be connected to the

power supply terminals.
The power unit for supplying the device must comply with NEC Class 2 as described by the

National Electrical Code(r) (ANSI/NFPA 70).
The power of all connected power supply units must total the equivalent of a power source

with limited power (LPS limited power source).

6.2

Power supply using Power over Ethernet (PoE)

"Power over Ethernet" (PoE) is a power supply technology for network components

complying with IEEE for 802.3af.

●

The power is supplied over the Ethernet cables used to connect the individual network

components with one another. This makes an additional power cable unnecessary.

●

SIMATIC MV500 is a PD (Powered Device), Type 1, Class 3 (max. 12.95 W)

Restriction of the power supply type

The IEEE standard 802.3af specifies two types of power supplies:

●

Voltage via wire pairs that are not used for data transmission (redundant wires).

●

Voltage via wire pairs that are used for data transmission (phantom power).

The Ethernet connection of the SIMATIC MV500 optical readers is four-wire. Power can only

be suppled via these four wires with phantom power. The voltage feeding device must

provide the phantom power.
The following Siemens switches with PoE provide phantom power:

●

SCALANCE X108 POE

●

SCALANCE XP208 POE EEC

●

SCALANCE XP216 POE EEC

●

SCALANCE X308-2M POE

●

SCALANCE XR324-4M POE

●

SCALANCE XR324-4M POE TS

●

SCALANCE XM-400 with Port Extender PE408 PoE and

PoE power supply SCALANCE PS9230 PoE or SCALANCE PS924 PoE

●

SCALANCE XR-500M with media module MM992-4POE or MM992-4POEC

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands