Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 54

Page: 54 / 238

Network and system integration

4.2 System configuration via PROFINET/PROFIBUS with CM

SIMATIC MV500

Operating Instructions, 06/2018, C79000-G8976-C494-01

4.2

System configuration via PROFINET/PROFIBUS with CM

①

Optical sensor or light barrier (for trigger signal)

②

Object with code

Figure 4-1

Example: System configuration via PROFINET IO/PROFIBUS DP-V1 with

communication module

System characteristics

●

The PROFINET/PROFIBUS connection is made via the CM interface of the optical reader

and a communication module.

●

PROFINET IO/PROFIBUS DP-V1 is connected to an S7 controller.

●

The optical reader is controlled via PROFINET IO/PROFIBUS DP-V1 using the Ident

profile block by the S7 controller.

●

The result is output via PROFINET IO/PROFIBUS DP-V1 to the S7 controller.

●

The optical reader is supplied with power via the communication module.

●

The optical reader is triggered either via digital I/O, S7 controller or via the built-in auto-

trigger function.

●

A PC/PG is connected via the Ethernet interface to allow adjustment of the device.

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands