Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 175

Page: 175 / 238

SIMATIC MV500
Operating Instructions, 06/2018, C79000-G8976-C494-01

175

Service and maintenance

10.1

Error and diagnostics messages

If there are operator errors or errors in processing mode, the optical reader outputs

diagnostic information. The diagnostic information can be read out as follows:

●

As a message via the WBM.

●

Via the LED display on the reader.

●

When using onboard PROFINET and FB 79 or Ident profile, in the device diagnostics.

●

When using the Ident profile, in the diagnostics.

10.1.1

Message types

For the messages, a distinction is made between the following message types:

●

Error messages

●

Warnings/notes

●

Read results

All three message types are displayed in the WBM.
Most messages of the "error message" type trigger a diagnostic interrupt on the relevant

PROFINET controller.
The following sections "Error messages" and "Error output of read results" describe all

messages, their meaning and the corresponding corrective measures.

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands