Siemens SICAM Q80 System Manual Download Page 76

Page: 76 / 240

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

Overview

Overview of all important values and a vector diagram for displaying phase angle between conductors

The minimum, mean and maximum values are displayed for:

U RMS, I RMS, Frequency, Symmetry, Total system power

Note

Observe the differences between the saved values and the online display:

For the values saved in the device for subsequent analysis, the following applies:

The

averaging interval

depends on the

user configuration

(default: 10 min, f= 10 s)

The Min/Max-values saved are calculated on the basis of the averaging interval.

This means that at the start of the interval, the extrema are reset, in order for fresh ones
to be calculated.

In 4-quadrant measurements, the power is summed up upon elapse of each interval.

For the online values (overview values, MODBUS)

The

averaging interval

has a

permanent

value of

1 s

These values only serve the purposes of display and queries and or not saved.

Extrema are the averaged

min/max-values since the start of the measurement

since the last reset; button:

Reset Min/Max.

In 4-quadrant measurement, the summation of the power since the measurement start or
since the last reset.

Summary of Contents for SICAM Q80

















































































































































































































































Siemens SICAM Q80, System Manual, Page: 76 / 240

Search results

Summary of Contents for SICAM Q80

Reviews: