manualshive.com logo in svg

Siemens SICAM Q80, System Manual, Page: 152 / 240

Share
Download
Siemens SICAM Q80 System Manual Download Page 152

 152

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.8

Client-Server configuration

When there are multiple measurement devices and different workstations, it is possible to construct a variety of
architectures.

Server (main computer)

Must always stay in active state

Retrieves the data from all measurement devices

Import and analysis of the data

Measurement configuration

Client-PC

Graphical output of the measurement and results evaluation

Measurement configuration

Notes

As the number of users increases, the display refresh rate decreases.

Data import and extending the interval of data which were 

just 

displayed is NOT possible! 

For this reason, import of data should be scheduled for times while no other work is being
performed. If data are being imported while analysis is running on the same PC, a warning
notification may be displayed. 

Close the software upon receiving this notification. Alternatively, switch to a view without any
measured data and delete the software using the menu command 

“Evaluation \ Delete

measurement data \ all open data”

.

Neither displayed measured data nor tables are automatically expanded as new data are
accumulated.

5.1.8.1

Setting up Client-Server operation

Server PC:

Measurement data folder: D:/SICAMQ80/Data/..

Database folder:

D:/SICAMQ80/DB/..

Share the folder: "D:/SICAMQ80/" as "SICAMQ80_ALL"

Example: Database entry for the measurement "Test_1" on 2/1/2012 

Topology: Berlin/Station_1/ST_230V/Room_1/

Database entry

Start

2/1/2012 12:00 AM

End

2/2/2012 12:00 AM

Root folder

D:/SICAMQ80/Data

Subfolder

Room_1/Test_1/2012-02-01 00_00_00

Frequency

Freq.dat

For display of the frequency, the file "Freq.dat" is opened from the path "D:/SICAMQ80/Data/ Room_1/Test_1/2012-
02-01 00_00_00".

Summary of Contents for SICAM Q80

















































































































































































































































Reviews:

No comments