manualshive.com logo in svg

Siemens SICAM Q80, System Manual, Page: 140 / 240

Share
Download
Siemens SICAM Q80 System Manual Download Page 140

 140

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.7

Automated operation with multiple devices

A measurement with multiple measurement devices can easily be automated. For such automated operation, the two
supplemental programs  

 Auto-Transfer

 and 

Autoreport

 are required.

SICAM Q80 Manager configures:

measurement devices

auto-transfer

autoreport

data base

Task assignment

To configure the measurement devices, use the 

SICAM Q80 Manager

. 

This starts the measurement and saves

the data in normal cases to the internal removable storage unit. Additionally, a running measurement can be
observed and cyclically evaluated.

Transfer of multiple devices' data to a temporary storage unit is performed with the program 

Auto-Transfer

.

There, the data await evaluated by Autoreport.

The program 

Autoreport

 accesses the data available from 

Auto-Transfer 

and cyclically generates a report

for each device.

The results generated by Autoreport are written to the database.

These programs appear as independent programs in the program group 

Siemens Energy\SICAM\ SICAM Q80

Manager\ SICAM Q80 Manager Auto-Transfer 

or

 Autoreport

142

148

142

148

Summary of Contents for SICAM Q80

















































































































































































































































Reviews:

No comments