manualshive.com logo in svg

Siemens SICAM Q80, System Manual, Page: 64 / 240

Share
Download
Siemens SICAM Q80 System Manual Download Page 64

 64

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

Supposing you have not yet begun a measurement and the device is in its 

Online and stopped 

state (connected):

Starting the measurement 

involves the following steps:

1.

Connection

: The software sets up a network connection.  

2.

Preparation

: The settings for the measurement task are written to the device. Then the device is ready to

measure.

3.

Start

: Data capture is started. (Clicking on "Start" right away causes all three steps to be performed

immediately).

The device state indicated is now 

Measurement active

. As long as the device is connected to the PC, data are

continuously transmitted to the PC via the communication network. This is absolutely necessary for the online display
but it makes heavy demands on the communication network's resources.

Clicking on 

Disconnect 

ends the link between the computer and the measurement device. This neither ends nor

disturbs data acquisition, since all measured data are saved to the internal removable hard disk.

The device setting indicated now is 

Off-line, measurement active

. After disconnecting from the device, you can close

the 

SICAM Q80 Manager

 software and deactivate the PC. To resume work, restart the program and re-connect the

PC to the device. You can connect and disconnect as often as desired.

In order to 

end the measurement

, it must be possible for the PC to reach the device via the network or modem

connection. Use the button 

Stop

. All folders on the hard drive are closed. Alternatively, the measurement can  be

ended by means of the 

device list on the Topology page

. There, you can stop multiple devices at the same time.

To stop, you 

don't 

need to connect, which causes the procedure more quickly. When 

connecting 

with a measuring

device, the current configuration is imported and the current measured values are immediately transferred, while for 

Stop

, only the stopping command is transferred.

Note

During active measurement and online monitoring, various pages of te 

SICAM Q80 Manager

are disabled.

Changes to the settings only take effect the at the start of the next session.

21

Summary of Contents for SICAM Q80

















































































































































































































































Reviews:

No comments