manualshive.com logo in svg

Siemens SICAM Q80, System Manual, Page: 25 / 240

Share
Download
Siemens SICAM Q80 System Manual Download Page 25

 25

Operation modes and settings

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.1.2

Topology

The table below shows the topology and administers the measurement locations assignment of measured data.

Context menu

Definition:

 Creates new topology entries

 

New Region:

 Generates a new entry for a region,

see also 

here

.

New Station:

 Generates a new entry for a station, see

also 

here

.

New voltage level

: Creates a new entry for a voltage

level, see also 

here

.

New feeder: 

 Generates a new entry for a measurement

location, see also 

here

.

Report

Show Autoreport log file…: 

Shows general log file of the Autoreport (start time, when ended...)

 

Show reports...: 

Opens a selection dialog containing all reports. the reports are saved to the same older as

the parameter sets.
Default: 

<Public documents>\ SIEMENS\SICAMQ80\Data\<feeder>\<Parameter set>\<Reportx>.pdf

Show meas. loc. file...: 

Shows the measurement location's log file.

Switch to analysis: 

Goes to the 

Evaluation

 page .

Measurement location

 

Set as passive

: Sets the measurement location to passive, in order that the device / measurement group is

assigned to another measurement location.

 

Activate

: Activates the measurement location, on the condition that it is not already active at another branch.

 

Delete

: Selected entry (entries) and all associated subentries are deleted.

Topology

Save topology: 

Saves the current topology

Export topology to...: 

Exports the current topology from an XML file.

Import topology from...: 

Imports a previously exported topology in XML format.

General

 

Properties

: Properties of the selected topology entry, see 

here

Note

When a device is parameterized, then this always refers to the current entries in the
topology. Thus, in the reports on a measurement location, different reports may be listed!
( e.g. due to exchanging devices, repairs etc.)

Any empty topology always shows the entries 

Collector \ Station \ Level

. These are required

for storing data from unknown measurement locations for Autotransfer and -report purposes.
These entries can not be deleted.

27

27

27

27

109

26

Summary of Contents for SICAM Q80

















































































































































































































































Reviews:

No comments