manualshive.com logo in svg

Siemens SICAM Q80, System Manual, Page: 157 / 240

Share
Download
Siemens SICAM Q80 System Manual Download Page 157

 157

Operation of the Software

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

6.3.1.1

Update-Information

6.3.1.1.1  Version 2.x

The structure of the parameter sets has been changed between the software version 1.0 and 2.0. When adopting
parameter sets from software version 1.0, note the following:

Old structure:

Measurement location /

 Parameter set name / ParameterSetName.nqa

New structure:

Region / Station / Level / Feeder / 

Parameter set name / ParameterSetName.nqa

1. Set up the topology so that the new branch name is the same as the name of the old measurement location. Then

in the evaluation, all already existing measurement data are assigned to there.

2. The available/old parameter sets can be loaded by means of the device list and the context menu item "

Load

parameter set..

". If a different measurement device than the desired one is set in this parameter set, you can

save the configuration as a template and later load it for any device.

3. All existing measured data assigned to a measurement location, which was not defined as a branch in the topology,

appear in the list of all measured data next to the topology.

General notes on "Load parameter set.."

By default, the parameter sets already defined for the branch, which is assigned to the device, are displayed.
Therefore, prior to this action, the the measurement device must be assigned in the topology. However, you can also
view and load parameter sets belonging to other branches in the dialog displayed. After loading, the device which had
been defined for the parameter set is activated. However, by saving the parameter set as a template, you can also
assign the parameters to a different device.

Branch1

-

ParameterSet11 (for device a)

-

ParameterSet12 (for device a)

-

..

Branch2

-

ParameterSet 21 (for device b)

-

ParameterSet 22 (for device b)

-

..

Selected device: "Device a"

1. "Load parameter set.." -> Load "ParameterSet11"

2. active device -> "device a“

or:

1. "Load parameter set.." -> Load "ParameterSet21"

2. active device ->„device b“

3. all further actions are carried out with device b.

6.3.1.1.2  Version 3.x

Due to the expansion of the settings, it is not possible to achieve 100% conversion. Only such parameters are set
which correspond appropriately. This applies in particular to event monitoring. For this reason, it is urgently
recommended to check all the pages of parameters! When the system detects conflicts, a notification is posted.

22

Summary of Contents for SICAM Q80

















































































































































































































































Reviews:

No comments