Siemens SICAM P 7KG7750 Manual Download Page 9

Page: 9 / 142

Contents

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

Data Logger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.11.1

Data Logger Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.11.2

Data Logger Limit Violation Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.11.3

Data Logger Binary States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.12

Overflow of Measured Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parameterization via PC Software

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1

Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

5.2

Overview of Parameterization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2.1

Overview of Parameterization 7KG7750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2.2

Overview of Parameterization 7KG7755 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3

Date / Time Settings and Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4

Dialog Window SICAM P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5

Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5.1

Connection / Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6

Screens Setting on SICAM P 7KG7750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.1

Basic Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6.2

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7

Input / Output Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.1

Binary / Relay Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.2

Information on Energy Pulse Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.2.1

Parameterization via Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.2.2

Pulse Time, Switch Off Time, Number of Pulses . . . . . . . . . . . . . . . . . . . . .

5.7.2.3

Parameterization of Energy Pulses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.2.4

Parameterization of Energy Pulses via Parameterization Software. . . . . . .

5.7.3

Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.4

Analog Outputs (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.5

Analog Inputs (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7.6

Binary Inputs (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.8

Additionals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

5.8.1

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

101

5.8.2

Device Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

102

5.8.3

Limit Value Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

104

5.8.4

Clock Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

105

5.9

Memory Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

106

5.9.1

Splitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

107

5.9.2

Mean Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

5.9.3

Power Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

111

5.9.4

Oscilloscope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

113

5.9.4.1

Characteristics of „Instantaneous Values“ Recording . . . . . . . . . . . . . . . . .

113

5.9.4.2

Characteristics of "RMS Value" Recording . . . . . . . . . . . . . . . . . . . . . . . . .

114

5.9.5

Parameterization Oscilloscope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

115

5.9.6

Limit Violation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

116

5.9.7

Binary States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

117

5.10

Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

118

5.11

Resetting Values in the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

120

Summary of Contents for SICAM P 7KG7750















































































































































Search results

Summary of Contents for SICAM P 7KG7750

Reviews:

Siemens SICAM P 7KG7750, Manual, Page: 9 / 142

Search results

Summary of Contents for SICAM P 7KG7750

Reviews: