Siemens SICAM P 7KG7750 Manual Download Page 5 | Manualshive

Page: 5 / 142

Siemens SICAM P 7KG7750 Manual Download Page 5

Foreword

5

Power Meter, SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

Information for your safety

This manual does not represent a complete listing of all the safety measures required to operate
the equipment (module, device) since specific operating conditions may make further measures
necessary. However, it contains information which you have to observe in order to ensure your
personal safety and in order to avoid material damage. The information is highlighted by a warn-
ing triangle and, depending on the degree of danger, is shown as follows:

DANGER

DANGER

means that death or severe injury

will

result if the measures specified are not taken.

•

Comply with all instructions, in order to avoid death or severe injuries.

WARNING

WARNING

means that death or severe injury

may

result if the measures specified are not taken.

•

Comply with all instructions, in order to avoid death or severe injuries.

CAUTION

CAUTION

means that minor or moderate injury

can

occur if the measures specified are not

taken.

•

Comply with all instructions, in order to avoid moderate or minor injuries.

NOTICE

NOTICE

means that property damage

can

result if the measures specified are not taken.

•

Comply with all instructions, in order to avoid material damage.

Note

Important information about the product, product handling or a certain section of the documen-
tation, which must be given particular attention.

«
...
3
4
5
6
7
...
»

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments