Siemens SICAM P 7KG7750 Manual Download Page 89

Page: 89 / 142

5.6 Screens Setting on SICAM P 7KG7750

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

5.6.1

Basic Screen Settings

Here you define fundamental properties of the display on the SICAM P 7KG7750.

Number of screens

Select the number of screens, which can be selected using the buttons on the front of SICAM P.
You can enter between 1 and 20 screens.

Automatic screen interval

In SICAM P, you can switch between screens either manually using the buttons or automatically.

•

0 s (=

Off

): manual switching using keys

•

1 s to

s: automatic switching after the period set; the device then switches automatically

from screen to screen on a loop.

Display illumination

You can enter the time the backlighting remains on in minutes here.

•

0 min (=

Off

): no backlighting

•

1 min to 98 min: after a button is pressed on the device, the back lighting remains on for the
time set.

•

99 min (=

): permanent backlighting

Display contrast

Here, you can adjust the contrast of the SICAM P display. The default value is 4.

•

Input options: 0 to 9

Summary of Contents for SICAM P 7KG7750















































































































































Search results

Summary of Contents for SICAM P 7KG7750

Reviews:

Siemens SICAM P 7KG7750, Manual, Page: 89 / 142

Search results

Summary of Contents for SICAM P 7KG7750

Reviews: