manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 96 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 96

5 

5.7 Input / Output Modules

96

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

5.7.3

Basic Settings

This dialog allows you to specify the I/O module (optionally) of your SICAM P.

There are two possibilities:

SICAM P is connected with PC (online)

1. Click the button 

Load slot configuration

 from device. The information will be loaded from 

the device and displayed on the screen.  

2. Parameterize the I/O modules.

3. Send the new configuration to the device.

A parameter set is prepared for a later transmission to a SICAM P (offline).

1. Define slot A for the corresponding I/O module. 

Note

To ensure proper energy registration, this value must not be lower than the value calculated in 
step 4. 

Note

This procedure ensures that the I/O modules displayed on the screen correspond to those in the 
device.

Note

These settings must correspond to the I/O modules in the device (refer to the ordering number, 
see chapter 1.3)!

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments