manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 130 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 130

6 

6.3 Procedure

130

Power Meter SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

6.3

Procedure

•

First, connect the SICAM P as described in chapter 6.2.

•

You can adjust the device manually or via programming software

Procedure at the device

•

Select 

Basic settings 

→

 Connection / Transformer

.

Select the range to be adjusted (e.g. AC 228 V).

•

In the menu, select: Calibrate.

A dialog window appears.

•

Enter the setpoint value for adjustment voltage and adjustment current. Default setpoints are 
the nominal ranges of the measuring ranges set under 

Connection / Transformer

. Optimal 

precision can be achieved by using these default setpoint values. If the default values are not 
available, make the appropriate changes.

•

Switch the adjusting device on with the setpoints.

•

Follow the instructions. SICAM P is readjusted.

Procedure for programming software

•

Establish the communication between device and programming software. 

•

In the menu, select: Calibration

A dialog window appears.

•

Select the element you wish to adjust: U or I

•

Enter the setpoints for adjustment of voltage and current. The setpoints given are the nominal 
values of the measurement ranges set under Connection / Transformer. These preset set-
points ensure optimum precision. If the preset values are not correct, change them accord-
ingly.  

•

Switch the adjusting device on with the setpoints.

•

Follow the instructions. SICAM P is readjusted.

Calibration of the 
selected input range. 
Please follow the in-
structions in manual! 
<ok 
<cancel

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments