manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 67 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 67

4

4.4 Basic Settings

67

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

4.4.4

Communication Interface

4.4.4.1

General Settings

Bus addres

Input address 1 to 254 

Baud rate 

•

Selection only for connection to a PC or Modbus. The following baud rates are allowed:
300 bit/s, 600 bit/s, 1200 bit/s, 2400 bit/s, 4800 bit/s, 9600 bit/s, 19200 bit/s, 38400 bit/s, 

57600 bit/s, 115200 bit/s.

•

The baud rate of the Profibus is supported automatically up to 12 Mbit/s with the selection 
being performed via the master station.

Parity

•

Only for Modbus (N = None, E = Even, O = Odd)

Protocol

•

SICAM P ASCII Protocol: PC RS485 (for connection to a PC via programming software)

•

Profibus DP (with firmware version V3 only) or

IEC 60870-5-103 (with firmware version V4 only)

•

Modbus RTU

•

Modbus ASCII

*bus address:112
*baudrate:   19200Bd
*parity:     E
*protocol:   IEC 103
>IEC 103 settings

<ok
<cancel

Note

The Baud rate is selected during parameterization (using SICAM P Par or the display). It can be 
set in the range between 300 bit/s and 115200 bit/s, for the IEC 60870-5-103 protocol, however, 
only in the range between 9600 bit/s and 38400 bit/s.

Note

At delivery, the following communication parameters are preset:

Address:

 

1

Protocol: PC-RS485
Baud rate: 

9600 bit/s

Parity: No

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments