manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 13 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 13

1

1.2 Delivery

13

Power Meter SICAM P 7KG7750/55, Manual
E50417-B1076-C340-A6, Edition 09.2013

1.2

Delivery

Delivery note

The power meter will be delivered in a cardboard box containing the SICAM P logo.

Contents of delivery

1 Device SICAM P

2 Panel mounting fittings (only 7KG7750)

1 Operating Instruction (Ordering no.  E50417-B1074-C339)

1 Return Card

1 Device Test Report

1 Battery VARTA CR2032

WARNING

Warning: Danger of explosion of the battery.

Nonobservance of the safety instructions means that death, severe
injuries or considerable material damages can occur.

•

Servicing of the battery circuit and replacing of the battery must be performed by qualified 
personnel only. Battery may explode if mistreated.

•

Do not reverse the polarity! 

•

Do not disassemble the battery! 

•

Do not completely discharge the battery! 

•

Do not throw the battery into a fire!

WARNING

Warning about battery disposal.

Nonobservance of the safety instructions means that death, severe
injuries or considerable material damages can occur.

•

When discharged, or when properly secured against short-circuit, lithium batteries can be 
disposed of through retailers or at depots run by competent organizations (e.g. in Germany 
GRS collection points).

Note

The lithium-batteries in the equipment are subject to special provision 188/A45 of the dangerous 
goods regulations of the different transport modes (as in edition 2003, lithium content and tests 
of UN Manual of Tests and Criteria).

This is only valid for the original battery or original spare batteries. For general transport security 
by shipment as freight: Electric equipment is only to be sent as freight if shut off.

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments