manualshive.com logo in svg

Siemens SICAM P 7KG7750, Manual, Page: 6 / 142

Share
Download
Siemens SICAM P 7KG7750 Manual Download Page 6

Foreword

6

Power Meter, SICAM P 7KG7750/55, Manual

E50417-B1076-C340-A6, Edition 09.2013

Statemant of Conformity

Qualified personnel

Commissioning and operation of the equipment (module, device) described in this manual must 
be performed by qualified personnel only. As used in the safety notes contained in this manual, 
qualified personnel are those persons who are authorized to commission, release, ground, and 
tag devices, systems and electrical circuits in accordance with the safety standards.

Use as prescribed

The equipment (device, module) must not be used for any other purposes than those described 
in the Catalogue and the Technical Description. If it is used together with third party devices and 
components, these must be recommended or approved by Siemens.

Correct and safe operation of the product requires adequate transportation, storage, installation, 
and mounting as well as appropriate use and maintenance.

During operation of electrical equipment, it is unavoidable that certain parts of this equipment will 
carry dangerous voltages. Severe injury or damage to property can occur if the appropriate 
measures are not taken:

•

Before making any connections at all, ground the equipment at the PE terminal.

•

Hazardous voltages can be present on all switching components connected to the power 
supply.

•

Even after the supply voltage has been disconnected, hazardous voltages can still be 
present in the equipment (capacitor storage).

•

Equipment with current transformer circuits must not be operated while open.

•

The limit values indicated in the manual must not be exceeded; that also applies to testing 
and commissioning.

This product complies with the directive of the Council of the European Communities 
on the approximation of the laws of the Member States relating to electromagnetic 
compatibility (EMC Council Directive 2004/108/EC) and concerning electrical 
equipment for use within specified voltage limits (Low-voltage Directive 2006/95/EC).

This conformity has been established by means of tests conducted by Siemens AG 
according to the Council Directive in agreement with the generic standards EN 61000-
6-2 and EN 61000-6-4 for the EMC directives, and with the standard EN 61010-1 for 
the low-voltage directive.

The device has been designed and produced for industrial use.

The product conforms to the standards IEC 60688, EN 60688 or DIN EN 60688.

Summary of Contents for SICAM P 7KG7750















































































































































Reviews:

No comments